WATER-EJECT.COM
Ready to start
Ready to start
Frequency: 0 Hz
Water eject programs
Full Range Sweep
ReadyFrequency Burst
ReadyProgressive Bursts
ReadyRandom Bursts
ReadyTip: Set your iPhone's system volume to maximum for best results. This slider controls only the in-app output level.
Algorithms are designed to eject water by maximizing speaker pressure.
Free tool to remove water from your iPhone speaker using sound frequencies. Same principle as Apple Watch Water Lock. Works on all iPhone models.
Every iPhone since the iPhone 7 has an IP67 or IP68 water resistance rating. But Apple is clear about one thing: water resistance is not permanent. It wears down over time from drops, repairs, and everyday use.
If your iPhone gets wet, Apple's official guidance covers what to do and what to avoid:
Do this
Avoid this
Apple's recommendations cover the charging port and internals. For muffled speaker audio specifically, sound frequency vibration can clear trapped water from the speaker mesh much faster than waiting for it to air dry on its own.
When water gets trapped in your iPhone speaker grille, it sits on the fine mesh covering the speaker opening. Surface tension holds the droplets in place, blocking sound from coming through clearly. That is why your speaker sounds muffled even when the rest of the phone works fine.
Water Eject plays low-frequency tones through your iPhone speaker. These tones cause the speaker diaphragm to vibrate rapidly, creating pressure changes that break the surface tension and push water droplets out through the mesh.
The Apple Watch has used this same approach since watchOS 3. When you turn the Digital Crown after swimming, the Watch plays a series of tones to eject water from its speaker. Water Eject brings that principle to your iPhone through Safari, with no app or shortcut needed.
Why low frequencies work best: Lower frequencies produce larger speaker membrane movement. Studies on droplet dynamics show that vibrations in the 60-300 Hz range are especially effective at dislodging water from surfaces. Our algorithms focus on this range for maximum water displacement.
Follow these steps for the best results when ejecting water from your iPhone speaker:
Remove your case
Cases trap water around speaker openings. Take it off so expelled water can escape freely.
Disconnect Bluetooth devices
Audio needs to play through the iPhone speaker, not AirPods or other connected devices.
Turn volume to maximum
Higher volume means stronger speaker vibration. This pushes more water out of the grille.
Hold speaker facing down
Gravity helps. Point the bottom speaker toward the ground so water can fall away.
Tap Start Water Eject
Let the full cycle run without stopping. Each program sweeps through the frequencies that work best for water removal.
Wipe and repeat
Wipe moisture from the speaker area and charging port with a lint-free cloth. Run 2-3 more cycles if audio is still muffled. Try Frequency Burst mode for stubborn droplets.
Pro tip: Gently tap the area near the Lightning or USB-C port while the cycle runs. This can help dislodge water from spots the vibration alone might miss.
There are several ways people try to fix a water-logged iPhone speaker. Here is how they compare:
| Method | Time | Works? | Risk |
|---|---|---|---|
| Sound frequency | 30 sec | High | None |
| Air drying | 4-24 hrs | Medium | None |
| Silica gel | 12-24 hrs | Medium | Low |
| Rice | 24-48 hrs | Low | Medium |
| Compressed air | Instant | Medium | High |
| Hair dryer | 5-10 min | Low | High |
| Pro repair | 1-3 days | High | None |
Sound frequency clearing is the fastest safe option for moisture trapped in the speaker mesh. Apple specifically warns against compressed air and external heat sources. Rice leaves starch dust that can get into ports. Air drying works but can take a full day.
Skip the rice. Apple says putting your iPhone in rice can cause small particles to enter your device and cause damage. If you want a desiccant, silica gel packets are a safer choice, but sound frequency clearing is much faster for speaker water.
Water Eject works on every iPhone with a browser. Newer models with higher water resistance ratings tend to respond especially well:
| iPhone | Rating | Max Depth |
|---|---|---|
| iPhone 16 series | IP68 | 6 meters |
| iPhone 15 series | IP68 | 6 meters |
| iPhone 14 series | IP68 | 6 meters |
| iPhone 13 series | IP68 | 6 meters |
| iPhone 12 series | IP68 | 6 meters |
| iPhone 11 Pro | IP68 | 4 meters |
| iPhone 11 | IP68 | 2 meters |
| iPhone XS / XS Max | IP68 | 2 meters |
| iPhone X / XR | IP67 | 1 meter |
| iPhone 8 / 8 Plus | IP67 | 1 meter |
| iPhone 7 / 7 Plus | IP67 | 1 meter |
iPhone SE (2nd and 3rd gen) has IP67 water resistance and works well too. Even older models without an IP rating can use Water Eject, though they may be more vulnerable to internal water damage.
Water Eject sends audio to both the bottom speaker and the earpiece, so both openings benefit from the vibration cycle.
Also works on other devices
The Apple Watch has had Water Lock since watchOS 3. After swimming, you turn the Digital Crown and the Watch plays tones that push water out of its speaker. It works really well.
iPhones have no equivalent feature. Despite being water resistant since the iPhone 7, Apple has never added a Water Lock mode to iOS. If your iPhone speaker sounds muffled after getting wet, there is no system setting or shortcut built into the phone to clear it.
Water Eject fills that gap. It uses the Web Audio API in Safari to generate speaker-clearing tones tuned for iPhone speaker dimensions. No Siri Shortcut needed, no app to download, no permissions to grant. Just open the page, set your volume to max, and tap start.
Water Eject handles surface moisture in the speaker grille well. But some problems need professional repair:
For these situations, visit an Apple Store or Authorized Service Provider for professional diagnosis. You can also contact Apple Support online to check repair options and pricing before visiting a store.
Remove your case, turn the volume all the way up, and hold your iPhone with the speaker facing down. Run a Water Eject cycle and wipe away any water that comes out. Run it 2 to 3 times if the speaker still sounds muffled.
No. Apple Watch has Water Lock, which plays tones to clear speaker water after swimming, but iPhones have nothing like that in iOS. Water Eject brings the same speaker-vibration approach to your iPhone through Safari, with no app or download needed.
Yes. It plays sound frequencies that vibrate the speaker membrane to push water out. Every iPhone since the iPhone 7 has IP67 or IP68 water resistance, so the speakers are built to handle moisture. The frequencies are within normal operating range and won't cause damage.
No. Water Eject runs directly in Safari using the Web Audio API. No app download, no Siri Shortcut, no permissions. There are Siri Shortcuts floating around online that play a single frequency, but this tool offers multiple programs covering a wider range for better results.
Start with 2 to 3 full cycles. Wipe the speaker between runs and test the audio. If it still sounds off after 3 cycles, switch to a different program like Frequency Burst or Progressive Bursts. If the speaker is still muffled after that, let the phone air dry for a few hours before trying again.
Apple says to tap your iPhone gently with the connector facing down to remove excess liquid. Then leave it in a dry spot with good airflow and wait at least 30 minutes before charging. Apple specifically warns against rice, compressed air, and sticking anything into the ports. For muffled speakers, water eject speeds up what passive drying does on its own by actively vibrating water off the speaker mesh.
Any iPhone that can open a web page and play audio. All iPhones from the iPhone 7 onward have water-resistant speakers with sealed acoustic mesh, which is exactly the kind of speaker that traps water and responds well to sound-based ejection.
It can clear the speaker mesh after a brief dip or splash. Run 3 to 5 cycles with the speaker facing down. If the audio is still muffled after that and 30 minutes of air drying, the issue may be deeper moisture. Apple recommends waiting up to 24 hours for full internal drying. Don't charge until the Lightning or USB-C port is completely dry.
Same idea. Apple Watch Water Lock plays tones through its speaker to push water out after swimming. iPhones don't have this feature built in. Water Eject does the same thing through your browser, with multiple programs to choose from instead of a single tone.
That alert means the Lightning or USB-C connector detected moisture. Don't try to override it. Dry the port area, unplug any cable, and let it air out for at least 30 minutes. The alert should clear on its own once the port is dry. Water eject focuses on the speaker, but drying the port is just as important if you need to charge.
